|
256-bit encryption
$500,000 protection
|
VIKING SPORT FISHING 82
The Viking 82 not only lets you take your
mansion to sea with you, it competes with the most agile
boat out there.
With its 10-degree
deadrise at the transom, the Viking 82 spent a good deal
of time at the Stevens Institute in tank testing to
fine-tune this unique running surface.
Viking is
all about clean lines, and to that end, more changes
have been made to “the way we’ve always done it.” You’ll
see lots more shape in the transom – for both aesthetic
reasons and to get more water sliding off to the sides
when backing down on fish.
If you thought you
could tell a Viking from a distance, you may have some
more studying to do. The 82 sports a much more dramatic
sheer than previous models. Shaping everywhere has
obviously been a major design-change target for Viking.
Everywhere you look you see more roundness and sleekness
– the front of the house, the crown in the deck, even
throughout the interior.
More information about the
74 can be learnt by calling Viking Yachts at (609)
296-6000.
Prop tunnels:
The purpose of tunnels remains the
same as they did on my old boat: to help reduce the
draft. Unfortunately, that goal is at odds with the
laws of physics, which hold that a certain amount of
propeller blade area is necessary for a certain
horsepower, speed, and boat weight. If you don't
have enough blade area, cavitation is the usual
result. Cavitation manifests itself as noise,
vibration, prop and rudder erosion, and degradation
of performance, with increased fuel burn and reduced
speed and range.
So how do you achieve the necessary
propeller blade area and avoid all the problems?
Generally, a larger prop diameter is more efficient than
a smaller diameter, so bigger props are the obvious
answer. Putting physics aside for a moment, that extra diameter
has a practical downside: It aggravates the draft
problem, since propeller tips are the low point on most
boats. There's only so much space for props between the
bottom of the boat and the bottom of the sea. We can't
move the bottom of the sea, but we can move the bottom
of the boat. This is accomplished with prop tunnels.
The
sides of the tunnels are parallel to the centerline
of the boat, and parallel to each other as well for
their entire length. The sides do not converge
either forward or aft. Looking closely at the black
lines drawn athwartship, you can see that at the
forward end of the tunnel, the shape of the tunnel
roof begins very flat, and then transforms into a
progressively tighter radius as we move aft toward
the transom. At the point of the propeller location,
very near the end of the keel on this example, the
tunnel reaches its smallest radius. Aft of this
point, from prop to transom, the shape can be
maintained as in this Viking, or might converge just
a bit to create a slight "nozzle" effect on some
boats.
In addition to having the right shape for the
tunnel, it is important to have the cleanest, most
undisturbed water flowing into and out of the
tunnel. This is done by avoiding discontinuities in
the hull bottom and locating "bottom clutter," such
as thru-hulls and transducers, out of the path of
the water flowing into the tunnels. Shaft strut and
rudder palms should be mounted flush, in indents
molded into the tunnel, if at all possible.
Finally, there's the question of how close the prop
should run to the tunnel walls. On installations
without tunnels, the guideline is to allow 15
percent of the prop diameter (4 ½ inches on a
30-inch prop) as clearance between the hull bottom
and the prop-blade tips, to avoid excessive
vibration. With tunnels, this can easily be
tightened up to 5 or 10 percent, and some designers
have successfully gone to nearly zero without undue
vibration. Obviously, this allows a few more inches
of prop diameter, for more blade area and efficiency, with
resultant speed, range, and efficiency gains and
without added draft.
So there you have it: reduced draft and fuel usage,
more speed and range, less cavitation and vibration.
Tunnels aren't necessary for all boats, but when
draft is a problem, they can be the answer.
The photos above show a
Viking
82
model. We can build any
Viking sportfishing boat model. Accurate and premium quality.
Custom model is our specialty. If you can take photos of
your boat, we can build the model for you. The process
is simple and easy. We need only a small commitment
deposit to start the process. The remaining balance
won't be due until the model is complete. Please click
here for
lead
time.
Nobody builds better yacht
models than ModelShipMaster.
Click to learn more:
Premium yacht models.
Click
to view our other Viking boats:
Viking 64,
Viking 65,
Viking 74.
|
